top of page

Cold Pour Products

Inductive Cold Pour Loop Sealant

Brewer Cote®

Brewer Cote® Inductive Cold Pour Loop Sealant is a one-component, pourable, sand and acrylic-modified asphalt emulsion used for sealing inductive wire loop slots in asphalt and Portland cement concrete. It is specially formulated for greater flexibility in both hot and cold climates, and it skins over quickly to form a waterproof barrier. This sealant meets and exceeds Federal and State specifications in Arizona and other states.

Features

  • Meets all Federal, State FAA, and Military Specifications

  • Resists hydrocarbons, gas, oil, and chemicals

  • Spray or squeegee application for customized results

  • Highly resistant to ultraviolet light and water degradation

  • Tough, durable finish that is skid-resistant and reduces cleaning costs

  • Beautifies your pavement investment

  • Eliminates raveling and is non-scuffing

Sizes Available

5-gallon pails / 53 lbs.

Colors Available

Black

Coverage

Approximately 15 linear feet per gallon, based on ¼” wide by 2” deep slots. Coverage will vary depending on the width/depth of the slot and type of application method. Not recommended for slots bigger than 5/8”. Two coats are recommended on sealed pavements; consult the project manager.

Description

Brewer Cote® Inductive Cold Pour Loop Sealant is a single-component pourable, sand, and acrylic-modified asphalt emulsion designed for sealing inductive wire loop slots in both asphalt and Portland cement concrete. It provides flexibility in varying climates and forms a waterproof barrier.

Surface Preparation

Pavement slots must be free of dust, dirt, and water prior to application. Use compressed air before applying the sealant. The slot may be slightly damp to help the penetration of the sealant.

Mixing Procedures

Leave the pail upside down prior to use. Mix well with a mechanical mixer to ensure the product is uniform and sand is disposed. Excess material should be removed immediately using a V-Squeegee to force the material into the loop and avoid excess waste.

Application

Ready to use. B.C. Loop Sealant can be applied by pressure feed, pump, directly from the container, or by pour pot. Do not apply on rainy days or when the temperature is expected to drop below 45°F during the next 24 hours. Tack free in one hour under normal conditions (77°F at 50% humidity). If traffic is unavoidable, broadcast fine dry sand over the surface. Drying time will vary depending on surface temperatures. Test for traffic ability before opening.

Important

Weather Limitations:
For best results, do not apply on rainy days or when the temperature is expected to drop below 45°F during the next 24 hours.

Drying Time:
Tack free in one hour under normal conditions (77°F at 50% humidity). Drying time will vary depending on surface temperatures. Test for traffic ability before opening.

Clean Up

Clean up with water prior to drying. Use Biodegradable PRISM® or a suitable solvent if needed.

Specifications

ASTM
Test Description
Min/Max
Resutls
ASTM-D 244
Viscosity Saybolt Furol
25 -150
125.0 sec. range
ASTM-D 244 (1)
Retained on No. 20 Sieve % max
0.10
0.02
ASTM-D 244
Particle Charge
Positive
Positive

Specifications on Emulsion

ASTM
Test Description
Min/Max
Resutls
2
Pumping Stability
Pass
Pass
D 244
Settlement, 5 Days, % max
5.0
Pass
D 244 (3)
Residue, % max
60.0
62.0

Specifications on Residue

ASTM
Test Description
Min/Max
Resutls
D 2170
Viscosity, 60° F. Centistokes, range
100-9500
3.9
D 2006-70 (4)
Maltene Distribution, Ratio, Range
0.7-1.4
1.1
D 2006-70 (4)
PC/S, Ratio, Min
0.50
0.8
D 2006-70
Asphaltenes, % max
11.0
9.5

Pavement Sealer Price Inquiries

Pricing on Brewer Coat Pavements Sealers and Seal Coating Specialty Products Available.

bottom of page