Receive a FREE Quote. Call (623) 931-3728 Today!
Brewer Cote of Arizona
Pavement Sealers
Resurfacer +
Asphalt Resurfacer
Resurfacer + is a milled blend of Asphalt, Selected Mineral Fillers, and Acrylic, designed to enhance the longevity of asphalt surfaces. It beautifies and protects both old and new parking lots, recreational areas, and driveways against moisture, water penetration, UV rays, and oxidation. Its tough, durable formula fills pavement voids and low spots, replacing fines lost during aging.
Features
-
Milled blend of Asphalt, Selected Mineral Fillers, and Acrylic
-
Designed for both old and new asphalt surfaces
-
Fills pavement voids and low spots
-
Tough and durable formula
-
Can be squeegee applied
-
Smooth and flexible surface
-
Increased resistance to fuel and chemicals
Sizes Available
-
5-gallon pail (54 lbs)
-
55-gallon drums (610 lbs)
-
Bulk Transport (10 lbs/gal)
Coverage
50-70 sq. ft per gallon, per coat
*Two coats recommended on unsealed pavements
Colors Available
Jet black
Description
Resurfacer + is a specially formulated asphalt resurfacer that enhances the appearance and durability of asphalt surfaces. It fills voids and low spots, providing a smooth and flexible surface resistant to various environmental factors.
Surface Preparation
Ensure the area is clean and free from loose material and dirt.
Mixing Procedures
Product may be diluted with a maximum of 20% water. Priming may be necessary on aged surfaces using one-part SS-1H and four parts water, applied at 1 gal per 100 sq./ft. Do not over-dilute. Two coats are recommended on unsealed pavements. Consult your project manager if needed.
Benefits
Product may be diluted with a maximum of 20% water. Priming may be necessary on aged surfaces using one-part SS-1H and four parts water, applied at 1 gal per 100 sq./ft. Do not over-dilute. Two coats are recommended on unsealed pavements. Consult your project manager if needed.
Application
Squeegee or use mechanical equipment to apply the product onto the surface. Coverage should be applied mixed (water, sand, and additives) at a rate of 50-70 sq./ft per gal, per coat. If necessary, an additional 10% water may be added for smooth application. Ensure ambient and surface temperature is at least 55°F and rising during application. Do not apply if rain is forecasted within the next 24 hours. Allow new asphalt to cure through the summer season before sealing.
Important
Weather Limitations:
Do not apply on rainy days or when the temperature is expected to drop below 50°F during the next 24 hours. On hot days, pre-dampen the pavement with a fog system. Ambient and surface temperature must be at least 55°F and rising during application.
Drying Time:
Maximum drying time is 5 hours at 70°F, 50% relative humidity. Final coat should cure for 24 hours.
Clean Up
Use water before the product dries. For sealer finish use biodegradable solvent.
Specifications
Method | Test Description | Min | Max | Results |
|---|---|---|---|---|
ASTM D244 | Weight per gallon | 11.0 lbs | 12.0 lbs | 11.2 lbs |
Polymer Modified % (Based on Asphalt Contnet) | 3% | Pass | ||
ASMA A-1 | % Non-Volatile | 50 | 60 | 55 |
ASTM D2042 | % Non-Volatile (Soluble in Trichloroethylene by wt.) | 20 | 35 | 30 |
D5 | Penetration-Base Asphalt | 10 | 42 | 35 |
D36 | Softening Point (Ring & Ball) | 195° | 210° | |
D217 | Asphalt Content, Weight % | 15% | 25% | 20% |
ASTM D3910 | Wet Track Abrasion (Grams per sq./ft) | 15.3 | 4.6 | |
Percentage Loss | 5% | 1.50% | ||
D4585 | Water Resistance | No Loss | ||
D2939 | Resistance to Impact | Pass | ||
D2939 | Resistance to Heat | Pass | ||
D4799 | QUV UV Aging, 1000 HAS. | Pass | ||
PAH % | < .10% | |||
Volatile Organic Compound (VOC) | < 8 G/L |
*Modified for Sand Seal, 8 pounds + 10 minutes