top of page

Pavement Sealers

Street Saver

Asphalt Sealer

Street Saver is a milled polymer modified, mineral stabilized asphalt and fiber reinforced emulsion designed to increase the life expectancy of asphalt pavements. It beautifies and protects both old and new streets, recreational areas, and airports against moisture and water penetration, ultraviolet rays from the sun, and oxidation. The tough, durable formula fills pavement voids and low spots by replacing fines lost during the aging process.

Features

  • Saves pavement

  • Better resistance to fuel & chemicals compared to competitive products

  • Increases life expectancy

  • Meets all state & public works specifications

  • Long-lasting

  • Stops raveling

  • Skid-resistant flexible surface that stays black longer

  • Polymer modified

  • Mineral stabilized

  • Fiber reinforced

  • Fills pavement voids and low spots

  • Tough and durable formula

Sizes Available

  • 5-gallon pail (ship wt 54 lbs)

  • 55-gallon drums (ship wt 610 lbs)

  • Bulk transport / jobsite-trailers

Coverage (with Aggregate)

​For road applications, Street Saver is applied at a rate of 30 to 50 sq/ft per gallon (3.4 to 5.5 sq yd per gallon) with aggregate.

Colors Available

Jet black long-lasting finish

Description

Street Saver is a high-quality asphalt sealer designed to protect and beautify asphalt pavements. Its polymer-modified, mineral-stabilized, and fiber-reinforced formula fills pavement voids and low spots, providing a tough and durable surface that resists moisture, UV rays, oxidation, and chemicals. It meets all state and public works specifications, ensuring long-lasting performance.

Surface Preparation

Ensure the area is clean and free from all loose material and dirt. Priming may be necessary on aged surfaces using one part SS1H and four parts water, applied at 1 gallon per 100 sq ft.

Mixing Procedures

Street Saver can be applied using a squeegee or mechanical equipment. It may be diluted with a maximum of 20% water if needed.

Application

Apply Street Saver onto the surface, ensuring even coverage. Two coats are recommended, allowing the first coat to dry thoroughly before applying the second coat. Check for trafficability after application.

Important

Weather Limitations:

do not apply on rainy days or when the temperature is expected to drop below 50°F during the next 24 hours. Ambient and surface temperature must be at least 55°F and rising during application.

 

Drying Time:

Drying time is approximately 8 hours maximum at 70°F and 50% relative humidity.

Clean Up

  • When wet: Clean up with water

  • When dry: Biodegradable solvent

Specifications on Aggregate (RTU)

ASTM
Method
Resutls
D2939-7
Weight Per Gallon
10 lb - 12 lb/gal
D2939-8
Residue by Evaporation
54 min
D5
Penetration of Bituminous
15-50
D36
Softening Point
> 200ºF
D562
Viscosity Stormer
60 min
N/A
Polymer % to Asphalt
5% - 15%
E303
Surface Friction, British Pendulum
>75
D3910
Wet Track Abrasion Test
<2g per sq/ft loss
D4799
QUV UV Weathering 1000 hrs
No Fading
D133
Ductility of Asphalt
5cm - 15cm
D4541
Adhesive Strength on Asphalt
>200 psi
D2939

Resistance to Heat

(No Blistering or Slipping)

Pass
D2939

Flexibility

(No Cracking or Chipping)

Pass
D2939

Resistance to Water

(No Softening or Emulsification)

Pass
D2939

Drying Time

(50% Humidity - Cure 24hrs)

Pass

Aggregate

Mesh - Sieve
Size Retained
#12 Mesh
2% - 10%
#16 Mesh
30% - 60%
#20 Mesh
20% - 50%
#30 Mesh
2%-10%
#40 Mesh
0% - 5%
#50 Mesh
0% - 5%
#70 Mesh
0% - 5%
#100 Mesh
0% - 5%

Pavement Sealer Price Inquiries

Pricing on Brewer Coat Pavements Sealers and Seal Coating Specialty Products Available.

bottom of page